The Harman PB105 Pellet Boiler has automatic ignition, automatic temperature control, and Harman’s patented pellet pro feeder and burn pot. Designed for easy access to the burn pot, the entire hopper component swings open for performing maintenance and cleaning. The PB105 packs 0 to 105,000 BTU and has a 205 lb. hopper capacity and an extra large ash pan.
14 Comments
We have a Kedel RTB pellet boiler, installed in 2013, and we are on our third service call this week. This particular problem seems to be electronic (the monitor screen died), but in the past, the internal auger failed, was rewelded, failed again, and was rewelded again. This week, after the original monitor screen was replaced (we were charged UP FRONT for the part- 6 degrees that day so no choice), it failed the next day for unknown reasons. It ultimately restarted after the 5 or 6th attempt over a few hours. Then, today, it failed again. The motor bringing the pellets to the burner died. We have NO CONFIDENCE in this boiler after only 4 years, and actually we lost confidence about a year ago when problems were coming up with disturbing regularity. We feel that we’ve got a lemon, but I have heard from another person who services Kedels (he used to work for the person who now services this one) that the Kedel manufacturer talked up this product to be much better than it is. We are ready to throw in the towel, eat the cost, and replace this furnace after 4 years. Right now, we are completely disenamored with this furnace and the small company who installed/services it. Has anyone else had bad luck with Kedel boilers?
i install the pb-105 4 years ago and its a great machine .i burn 7-8 palet or pellet a year .(way to big house for the spec and it do the job anyway) i have a 7500 ft/2 house with the garage heat exchanger for air , radiant floor heating in my garage and a h2o to preheat the water for my water tank.
exept some asshole to the initial setting to calibrate the air flow on my system (i install a ajustable bolt to calibrate inlet flow trap) its perfect. may be not the most efficient on the market but really low maintenance and reliable…i recomand it
Hi
I have been trying to look up harman pb105 on the internet with no luck is this company still in operation if so could you please pass on contact info.
Thanks
the pellets are not coming down to the burning pot only a few then the feeder comes on and they do not keep coming down what could be wrong
Installed mine a year ago in interior Alaska (2012) — so super-cold temperatures down occasionally to -50F — in a 3500 well-insulated 2-story with daylight basement. It heats wonderfully and has oddly enough saved on my electric bill over my old cheapo oil-fired boiler because it has a reservoir of hot water that responds quickly. While I love this machine and would not trade it, it does come with a lot of maintenance and tending. The biggest problems I have had are with the aquastate and with the ignitor. The system started out great, but after a year, I’m beginning to have problems with the system automatically lighting due to a failing ignitor (which I’ll have to replace periodically at about $100 each time). The aquastat is also a cheaply made device that sits in a well at the top of the boiler, fixed in place with a coiled spring that is darned near impossible to install correctly and which is prone to failure, causing overheating. As a result, I’m having to replace this ($35) as well. One design issue that I dislike is that you cannot easily reach the burn pan to properly clean it without swinging open the entire boiler, which requires shutting the system down (unlike a normal pellet stove). Technically, you can get your hand into the access door, but it is hard to manuever a tool inside the burn box to scrape it properly. All these things aside, the money I’ve saved compared to burning oil is tremendous — and if I had it to over again, I would install this unit again.
I have a harman pb 105. I have encountered a few dealers that are simply not capable of installing this unit. Technically you need a plumber and an electrician to do the work properly and to code. I have read the user guide many times now and can practically teach courses on this thing. There are a lot of easy common things that i find installers either neglect to do or dont do properly. The aquastat installation in the top of the unit requires the brass spring be pushed onto it nice and snug so it can conduct heat from the immersion well to the sensor. My installer originally looked at that bag and tossed it to the side. They also left saying it might take an hour to get up to temp… So i left it alone thinking they are from a harman dealer they must know. Turns out after 45 minutes the unit coded out because it didnt get up to temp despite having a raging fire inside. Installed that spring on the aquastat and made sure it was snug and whala turns out it normally takes about 20 minutes for this boiler to go from cold to having a good fire in it.
got pellet stove instaled 3 months ago and it does not work! Sitting in the cold most of the time. Contractor gives alot of excuses to why its not working. like to much wind under house . So We insulated under house the best it could be insulated. the stove still will not come to temp. i guess they will say oh the moon needs to be alighne with saturn before you get temp. would not recomend A pellet boiler stove to anyone! And not to many heating contractors service or know anything about pellet boilers so you might be stuck with one contractor that treat you bad and leave you without heat for days at A time. I would strongly recomend people to not buy A pellet boiler to many problems with it.!!!!!!!!
Purchased 11/25/12 Installed by dec 1 and all I can say is WOW. plumbed in series and it has taken care of all my heating needs. Direct vent saved me $2000.00. I knew from get go any pellet device is NOT plug and play. I reccomend
Just installed a harmon pb105 pellet boiler. Removed the buderus oil boiler completely from the system. Installation was a breeze. Heating 4500 sq ft ranch with radiant heat in cellar and first floor. Second floor or attic has baseboard radiators. Hot water is also off the boiler loop.thru a supercell storage tank. We are using and average of 2.5 bags of pellets a day. Boiler is more then able to supply all our needs. The next week will be including a front walkway for ice melt. Just waiting for a heat exchanger and antifreeze. I have installed all parts of this system and the pellet boiler is the easiet so far. I highly recommend this boiler…..
Heated a 4800sq.ft. ranch last season. Had some issues with routing of the wire and automaticity of the machine, which I attribute to softwood pellets. All in all I think it is amazing. Reduced my heating costs by 66%. Pellets are the key. Get some bad ones and life is miserable. I would recommend this boiler to anyone. Expensive to install. I’m running 2 24″X24″ heat exchangers on 2 furnaces(dual zone)and it keeps the house at 66 without difficulty. On days below 10 degrees it’s a struggle and needs just a little help first thing in the morning to get the water temp up to 180.